[Cause]
An error occurred in the connection to the device with the displayed MAC. The number is a ControlNet error code.
[Countermeasure]
Refer to the cause code. If there is no cause code, refer to the system manual or the ControlNet error codes defined in ‘ControlNet Specification’.
The error codes described below are defined in ‘ControlNet Specification 2.0’. If the device cannot be connected normally, the controller generates a STOP error in the following format.
PRIO-156 CNET Error xxyyyy Bd # MAC ##
The error code (xx yyyy) is a ControlNet error code defined in ‘ControlNet Specification’. The code is expressed in hexadecimal (base 16). The first 2 digits xx indicate the general status, and the remaining 4 digits yyyy indicate the extended status.+------------------+-----------------+-------------------------------------------------------------------------------------------+ | xx | yyyy | Annotations | | Universal Status | Extended Status | | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x00 | | The service has normally ended. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0100 | Connection is in use, or duplicate transmission is open. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0103 | The transfer level and the trigger combination are not supported. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0106 | Ownership competition. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0107 | The connection cannot be found in the target application. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0108 | Connection type is invalid. The type of connection or priority of the connection is in | | | | question. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0109 | Connection size is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0110 | Equipment not yet configured. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0111 | RPI is not supported. There may also be a problem with the connection timeout multiplier. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0113 | The connection manager does not support more connections. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0114 | Key fields do not match equipment with the supplier ID or product code. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0115 | Key field product types do not match equipment. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0116 | The major or minor revision in the key field does not match the device. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0117 | Connection point is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0118 | Configure format is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0119 | The connection request has now failed because there is no open control connection. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x011A | Target application does not support more connections. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0203 | The connection is timed out, so it cannot be terminated. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0204 | Timeout waiting for the response to an unconnected send. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0205 | Invalid parameter in the unconnected send service. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0206 | The message is too long for the unconnected message service. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0301 | No buffer memory. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0302 | No network bandwidth for data. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0303 | No tag filter. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0304 | Not configured to send real-time data. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0311 | The port specified in the port field cannot be used. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0312 | The link address specified in the port field cannot be used. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0315 | The path field type or field value is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0316 | Terminated because the path and connection do not match. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0317 | There is no field, or the coded value of the network field is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0318 | The link address to the local side is invalid. | +------------------+-----------------+-------------------------------------------------------------------------------------------+ | 0x01 | 0x0319 | No secondary resources are available. | +------------------+-----------------+-------------------------------------------------------------------------------------------+
+------------------+---------------------+--------------------------------------------------------------------------------------------+ | xx | yyyy | Annotations | | Universal Status | Extended Status | | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x01 | 0x031A | The connection has been set. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x01 | 0x031B | A direct connection has been set. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x01 | 0x031C | Other | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x01 | 0x031D | Redundancy connection does not match. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x02 | None | The service requests could not be processed because the resources of the connection | | | | manager were not available. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x03 | None | The connection number specified in the Get_Connection_Data service is invalid. This error | | | | code is also returned when the specified connection cannot be found in the | | | | Search_Connection_Data service. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x04 | 0-based word offset | The path field type is invalid. The extended status is the word offset (0-based) to the | | | | word where the path error occurred. The offset starts at the first word after the path | | | | size. This error is not returned if an error occurs while parsing the connection path. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x05 | 0-based word offset | The path destination is invalid. The extended status is the word offset (0-based) to the | | | | word where the path error occurred. The offset starts at the first word after the path | | | | size. This error is not returned if an error occurs while parsing the connection path. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x07 | None | Connection lost. This error code is used when a Get service or Set service is performed | | | | using a connection. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x08 | None | The connection manager does not support the requested service. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x09 | Index for Elements | Data field error. The extended status is the index to the error location in the data | | | | field. If the data field has a configuration revision number, that number is always at | | | | index 1. If an error occurs in a Get service or Set service, the extended status indicates | | | | the failed attribute number. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x0C | Options | The service cannot be executed while the target is in its current state. The first word of | | | | the extended status is optional and may contain the current target state. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x10 | Options | The service cannot be executed during the current state of device processing. The first | | | | word of the extended status is optional and may contain the current device state. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x11 | None | Response data are too large. This indicates that the error code is used when the data | | | | requested in the Get service is too large to accommodate the cache. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x13 | None | Insufficient data received. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x14 | Attribute ID | The connection manager does not support the properties specified in the FIND service. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x15 | None | Overreceived data. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x25 | 0x0114 | Key fields do not match equipment with the supplier ID or product code. . Use the error | | | | code when the path contains a key field. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x25 | 0x0115 | Key field product types do not match equipment. . Use the error code when the path | | | | contains a key field. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x25 | 0x0116 | The major or minor revision of the key field does not match the device. This error code is | | | | used if the path contains a key field. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0x26 | None | Path size is invalid. | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0xd0 | 0x0001 | Connection is closed or stopped (used in adapter mode). | +------------------+---------------------+--------------------------------------------------------------------------------------------+ | 0xd0 | 0x0002 | Opening the connection is pending (used in adapter operating mode). | +------------------+---------------------+--------------------------------------------------------------------------------------------+